A gas tankless water heater's fan may continue briefly after the hot-water tap closes as part of normal operation. A sound that continues without stopping, changes noticeably, or accompanies an error needs model-specific assessment; there is no universal number of seconds that proves every unit is operating correctly.
This explanation concerns gas tankless equipment with combustion fans, rather than electric tankless models. Before deciding that the unit needs a fan or a flush, identify the model and describe when the sound occurs. A closed tap is one observation, not a complete diagnosis of the appliance.
Why the fan does not always stop with the water
Rinnai's homeowner FAQ explains that its fan can run for a short time after water flow stops. The stated purposes are maintaining consistent temperature during rapid starts and stops and exhausting residual flue products. The FAQ says the fan then stops on its own; it does not give a fixed timer for every model.
That explanation supports recognizing a short finishing cycle. It does not establish that a fan which never stops is behaving normally. Compare what you observe with the exact manual, and tell the service provider whether the behavior is familiar or newly different. Avoid turning a broad brand FAQ into a diagnosis of your installation.
The sound may involve another operating function
The Noritz EZ/NRCR owner's guide, page 30, describes fan or motor sounds after operation and relates them to quicker reignition and stable temperature. For NRCR models, it also describes automatic operation without hot-water use for recirculation, freeze prevention or prevention of stagnant water.
Those are model-specific explanations for why equipment may be audible even with a closed tap. They do not identify the component you are hearing. When calling for service, say “a steady whir after the shower” or “a repeating motor sound between uses” rather than declaring that the combustion fan is defective.
If the installation has recirculation, share that information and any known schedule. Do not change installer settings to test a theory. Ask the professional to distinguish the expected operating cycle from a fault using the manual that applies to the equipment. Recirculation design is a separate question from this post-use sound.
Record the pattern without opening the unit
A useful observation can be made from a safe, ordinary position near the appliance. Keep the cabinet closed and avoid reaching into the unit or touching hot components. You are gathering a description, not attempting a mechanical test.
- Record the make and complete model number from an accessible label or existing paperwork.
- Note which fixture was used and when its hot-water flow stopped.
- Time the sound you actually hear, including whether it stops by itself.
- Describe whether it is steady, intermittent, scraping or newly louder.
- Note any displayed message and any change in hot-water delivery.
- Record whether another person or appliance was using hot water during the observation.
If the behavior is intermittent, one clear observation is more useful than repeatedly cycling taps to provoke it. A short recording may help explain the sound if you can make it safely. Do not remove covers or stand near an unsafe condition to obtain evidence.
A displayed code changes the service conversation
The Rinnai RE/VE manual, page 51, identifies code 61 as a combustion-fan condition. The Navien NPE-A2/S2 user's manual, page 17, labels E109 as abnormal fan-motor operation. These examples show why the exact display and model matter.
The numbers are not interchangeable brand-wide diagnoses. Share the message as displayed and ask a licensed professional to interpret it against the applicable manual. Leave fan, gas, venting and electrical checks to that professional. A sound alone does not justify ordering a replacement part or descaling as the assumed remedy.
If the unit also stops delivering hot water, the existing no-hot-water guide addresses that broader problem. Keep this article's narrower question separate: what explains operation after a tap closes, and what information will help assess a change?
Know when routine observation should end
Normal-cycle explanations do not excuse a dangerous condition. The Noritz manual warns against use with a displaced, damaged, clogged or corroded intake/exhaust pipe. If you notice an unsafe vent condition, stop using the appliance and seek appropriate professional help; do not alter the vent to quiet the sound.
If you smell gas, leave the building without operating electrical switches and contact the gas supplier from outside; follow its instructions. Do not wait for a routine plumbing appointment or stay beside the heater to record the noise. The manufacturer's safety instructions take priority over this sound checklist.
For a persistent change without an immediate hazard, bring the model, display message and observation to the service discussion. Ask what diagnosis is proposed before agreeing to parts or maintenance. The diagnostic-appointment checklist can help organize the records and safe access.
Common questions
How long should the fan run after the tap closes?
There is no universal cutoff in the sources used here. Rinnai describes a short period, while the Noritz guide explains model-specific operating sounds. Check the exact manual and report a persistent or changed pattern.
Does a running fan mean the burner is still firing?
Fan sound alone does not establish burner operation. Rinnai describes continued fan operation after water flow stops. Ask the professional to interpret the unit's display and behavior without opening the cabinet yourself.
Should I unplug the heater to stop the noise?
Do not use power interruption as a workaround for unexplained sound. Follow the exact manual's safety guidance and seek professional assessment. Record the pattern and any displayed message instead of improvising a reset sequence.
Discuss tankless operating changes with KCB
KCB Plumbing serves Orange County from Costa Mesa. Call (714) 894-6520 Monday–Friday, 7 AM–6 PM, and Saturday–Sunday, 8 AM–5 PM to discuss the model, sound pattern and proposed diagnostic scope.
View Service DetailsLast updated: October 16, 2026
About the Author
KCB Plumbing
Plumbing guidance from KCB Plumbing, based in Costa Mesa and serving Orange County since 1998.
Have a plumbing question? Call KCB Plumbing at (714) 894-6520 (Monday–Friday, 7:00 AM – 6:00 PM; Saturday–Sunday, 8:00 AM – 5:00 PM).